Commercial & Industrial Epoxy Floor Coatings in College Station TX - a floor for real use
Worn, stained or peeling shop floor? We test the slab, pick the resin for your spills and traffic, and plan around your shutdown.
- Licensed and insured.
- Free estimates at your property.
- We reply within 1 business day.
What does a commercial epoxy floor in College Station involve?
Commercial & industrial epoxy floor coatings in College Station, TX start with grinding the concrete clean and end with a resin system picked for what your floor faces, from spills and temperature swings to carts, forklifts and how long you can close.
Most business owners call us when bare concrete is soaking up stains, an old coating is peeling in the traffic lanes, or the floor won't clean up the way the business needs it to. The price moves with the square footage, how much grinding and crack repair the slab needs, whether an old coating has to come off first, and which resin fits the work. The schedule turns mostly on how long you can close, because the floor has to cure before people and equipment go back on it. I'll put your own figure in a written estimate that lists the prep along with the finish, so you can see where the money goes.
How we install commercial and industrial epoxy floor coatings
On a business floor I start with questions. What spills on it, how hot or cold does the space get, what rolls across it, and how long can you close? We pick the resin and plan the schedule around those answers, and we test the slab before we commit to a system, because a coating is only as good as the concrete under it. Then our crew grinds the surface open so the resin has something to grab, fills cracks and pits, and puts down the primer and coats the system calls for. The area stays closed off until the floor has cured enough to use.
Not every space needs a full industrial system. For a small shop or an office entry where getting back in fast matters most, a polyaspartic floor coating may suit you better, and if your garage at home could use the same treatment, take a look at our garage floor coatings.
Smooth finish for dry, rolling traffic
A smooth, high-build coat suits warehouses, storerooms and showrooms where carts roll and the floor gets swept or mopped often. It's the easiest finish to keep clean, though it gives up some grip when it's wet.
Textured finish for wet or oily areas
We work grit into the coat for wash bays, kitchens and work areas where water or oil ends up underfoot. It gives better footing, and the trade-off is a surface that takes a bit more scrubbing.
Commercial epoxy floor coatings in College Station, from the permit question to the slab
In College Station, the city's Building Division issues permits before construction on a new structure, a remodel or a renovation, and its list names that work, not floor coating, so the list alone doesn't settle whether a coating job needs a permit. Before work starts we check with that office about your job and take care of the permit when it falls to us. If you'd rather ask them yourself, the division answers permit questions at cspds@cstx.gov or 979.764.3570.
We're based in College Station and work in Bryan, Navasota and the cities around them. A lot of the business floors we see are working slabs with years of oil, old sealer or a tired coating that has to come off before anything new will stick, so we size the prep to that at the estimate. We see the same kinds of floors on jobs in Bryan and Navasota.
Why College Station businesses call Mainstay for their epoxy floors
I do every estimate myself
I come out for the estimate and first visit, and our crew works with a lead installer on site. I come back to walk the finished floor with you, so the person who scoped the job is the one who checks it.
Careful prep since 2020
I learned coating work on an experienced installer's crew and started this business in 2020, and careful prep is what we're known for. That matters because floors fail in the concrete under the coating, not in the shine on top.
Licensed and insured, every job
We're licensed and insured. It's the first thing worth asking any crew you're about to let into a working building.
City registration before any permit
College Station requires contractors to register with the city before getting a building permit, and when a permit falls to us we take care of it. You'll hear what we found out before anything gets scheduled.
I'd rather tell you up front that a slab can't carry the system you want than put down a floor that lets go in a year. Request an estimate or call (979) 393-7012, and I'll come look at the concrete.
Request a quoteGet a written estimate for your commercial floor
We reply within one business day, by phone or email, to set a time for me to see the floor. The estimate is free, done at your property and comes with no obligation.
What happens after you call about a commercial epoxy floor?
Call or send the form
I answer the first call or get back to you, then we set a time for me to come see the floor. It helps if you can tell me roughly how big the space is and when you could close.
I look at the slab
I check the concrete for moisture, cracks and old coatings and ask how you use the space. Then I send a written estimate that lists the prep along with the finish, so you see what the price is made of.
Our crew preps and coats
Once you say go, our crew does the grinding, prep and coating with a lead installer on site. When it's done, I walk the finished floor with you.
Frequently asked questions
How much does a commercial epoxy floor cost in College Station?
Epoxy floor coating in College Station usually costs about $4 to $6 per square foot, including materials, floor preparation and application. That's the area's general range for epoxy, garage and basement floors included, so a business floor that needs heavy grinding, crack repair or a tougher resin can land outside it. Your written estimate gives the figure for your own floor, and our work is backed by our satisfaction guarantee.
How long does a commercial epoxy floor take to cure before we can reopen?
One maker's epoxy can take light foot traffic after 24 hours, light vehicles after 72 hours and heavy traffic after 7 days. Those times assume an average of 70 degrees and 50% humidity, and a cooler building takes longer, so we plan the shutdown around your space as it really is. If you can only close briefly, ask about MMA resin, which cures quickly and is often chosen when installation time has to stay short.
How do I choose between epoxy and urethane for a commercial floor?
Lean toward epoxy when the floor sees heavy chemical exposure, and toward urethane when the space swings sharply between hot and cold. Epoxy brings durability and chemical resistance, while urethane is more flexible and better at handling thermal shock, the strain of a sudden temperature change. That's why the questions about spills and temperature come first at the estimate.
What causes an epoxy floor to lift or peel off the concrete?
Too much moisture in the slab can make a coating debond, or let go of the concrete, and break down, which is why makers generally require moisture testing before installation. A test only shows the slab's condition at the time and in the spots tested, so ask any contractor when and where they tested. We'll show you where we tested yours.
Should a commercial epoxy floor be slip-resistant in wet or oily areas?
In those areas, one maker recommends adding slip-resistant additives to the coating, especially under heavy foot traffic. The same maker puts responsibility for meeting current safety standards and local floor friction requirements on the end user, which here means the business, so it's worth checking what applies to your kind of space before we pick a finish.
How do I prepare my building for an epoxy floor installation?
Keep the heating or cooling running steady, plan for airflow and keep open flames away from the work. One maker's epoxy needs a floor at least 50°F and a surface above the dew point, the temperature where moisture condenses, with stable temperatures through application and cure. Another warns that solvent-based products are extremely flammable and calls for shutting off pilot lights and ignition sources such as electrical motors, along with good cross ventilation before installing.
Other floor coatings we install
Garage Floor Coatings
If your home garage takes a beating too, a garage floor coating gives you a cleaner, tougher surface for cars, tools and hobbies, built on the same careful slab prep.
Polyaspartic Floor Coatings
Ask about a polyaspartic system if you're working around a tight closing window, since it sets up quickly and can mean fewer days with the floor roped off.
College Station, TX
Book an on-site look at your floor
Have your square footage, what the space is used for, what spills and rolls across it, and your shutdown window handy, and the first visit goes quicker.